PRODUCTS
Fax: 0575-87215311
Web: www.cntongqiu.cn
Tel: 0575-87381708
0575-87386708
Technical R&D Department Tel: 0575-80706629
Email: cntongqiu@cntongqiu.com
Address: No. 2 Hongyan Road, Feida Industrial Park, Paitou Town, Zhuji City, Zhejiang Province
Steel-lined PTFE (polytetrafluoroethylene) isostatically pressed flanged composite pipe
Classification:
Keywords:
Valve pipeline
Product details
The steel-lined PTFE pipe with isostatic pressing and flanging is manufactured by employing an isostatic pressing process to produce the PTFE liner. The sintered PTFE liner is then drawn into a steel tube using a tight‑lining technique, followed by stress relief and final flanging of the sealing surface.
Product Features
1. Pressurizing the autoclave increases the density of polytetrafluoroethylene and enhances its resistance to permeation.
2. Under conditions involving highly corrosive media, composite pipes and fittings with a nominal diameter ≤ DN250, operating within a temperature range of –60°C to 200°C, may be used in vacuum service within this same temperature range.
3. The inner lining layer, after stress relief treatment, effectively addresses the issue of expansion and contraction caused by temperature fluctuations during operation.
Dimensional data for the isostatic pressing flanging process of steel-lined PTFE (unit: mm)
| Nominal diameter | DN25 | DN32 | DN40 | DN50 | DN65 | DN80 | DN100 | DN125 | DN150 | DN200 | DN250 | DN300 | DN350 | DN400 | DN450 | DN500 | DN600 |
| Straight pipe dimensions | ≤1000 | ≤2000 | |||||||||||||||
| Liner thickness A | 3.5 | 3.5 | 3.5 | 4 | 4.5 | 4.5 | 5 | 5 | 5.5 | 6.5 | 7 | 8.5 | 9 | 9 | 9.5 | 10 | 10 |
| Liner thickness B | 3.5 | 3.5 | 4 | 4 | 4.5 | 4.5 | 4.5 | 5 | 6 | 6.5 | 7 | 8.5 | 8.5 | 9 | 9.5 | 10 | 10 |
| Seal face thickness A | 3 | 3 | 3 | 3 | 3.5 | 3.5 | 4 | 4 | 4.5 | 5 | 5.5 | 7 | 7 | 7 | 7.5 | 8 | 8 |
| Seal face thickness B | 3 | 3 | 3 | 3 | 3.5 | 3.5 | 3.5 | 4 | 5 | 5 | 5.5 | 7 | 7 | 7 | 7.5 | 8 | 8 |
Note:
1. The minimum dimension shall not be less than 100 mm; for DN200 and larger, when the temperature exceeds 150°C, the length shall not exceed 1000 mm; for DN600 and larger, this table is omitted.
2. For isostatic pressing, straight pipes and pipe‑fitting flanges must use FF faces.
3. Pipe fitting dimensions are detailed in Schedules 4.6 through 4.8;
4. The minimum outer diameter of the end flange surface shall comply with HG/T 2437; see Appendix Table 4.20 for details.
Related products
ONLINE MESSAGE
*Note: Please make sure to fill in the information accurately and maintain smooth communication. We will contact you as soon as possible